8778275 -Hoppe Automatic Lock Gear – HLS-9000 Series

$268.89

Part Number 8778275 Hoppe Automatic Lock Gear- Roller Pin version, 16mm faceplace, 14mm deadbolt, 36 inch handle height. This version require a European profile lock cylinder to active the deadbolt.  This will not work with a handle trimset that uses an American cylinder with a tailpiece.

 

 

Available on backorder

SKU: 8778275 Category: Tags: , , , , Product ID: 14928

Description

8778275 Hoppe Automatic Lock Gear.

The Hoppe #8778275  Automatic Lock Gear, HLS-9000 Series with Roller Pin – No Shoot bolt, 16mm Faceplate, Roller Pin Version. 35mm Backset, 14mm deadbolt throw.

Hoppe multipoint door locks are the absolute best multi point lock to have installed on your hurricane rated impact door. The multipoint lock bodies are made of stainless steel and is perfect for any environment. We have seen many of the older multipoint lock systems such as FUHR and G.U., corrode and rust in seacoast conditions. In the future when you change your locks Hoppe is a great brand to go with.

  • It is also important for you to replace your house or condo locks especially if you live near the ocean because of these reasons:
  • Salt can rot the wood and does damage to locks as well if not cleaned and serviced periodically.
  • Keep your home secure with weather, fault and intrusion resilient Hoppe multi-point door locks
  • Approved for Hurricane HVHZ zones in Florida Miami-Dade Counties
  • Easily open and close your door with minimal effort.

Component Specifications:

Below are the exact details of this particular Hoppe automatic multipoint lock component. Other variations are available.

Component Details

Brand:      Hoppe
Series:      HLS-9000, Handle Above European Profile Cylinder
Configuration:   Multi-point Locking System
Component:     Locking Gear
Model Number:    8778275
Activation:      Automatic, Multi-points activate when door closes, Turn thumb turn to lock securely.
Faceplate Width:    16mm (5/8")      
Lock Points:      Roller Pin, No Shoot bolt
Handle Height:     36" From Bottom of Door to Center of Handle.
Backset:      35mm (1 3/8")  Measurement from Edge of Door to Center of Handle
PZ Dimension:    92mm (3 5/8") Center of Handle to Center of Key Hole.
Dead Bolt Throw:    14mm ( 1/2") Center of Handle to Center of Key Hole.
Multi-Point Position:    Roller Pin @ 750mm ( 29 1/2") Down from Handle  /  6 1/2" up from bottom of door.
Bottom Roller Position:   6 7/16" up from bottom of the door on all lock gears
Roller Release trigger:   42 1/2" up from bottom of the door on all top extensions
Trimmable:      Yes, Maximum Cutoff 60mm (2 3/8")
  • Multi-points automatically extend when door closes
  • Turn thumb turn to lock
  • Combine Top Extension with Gear for complete lock
  • Faceplate width: 16 mm
  • Handle height: 36” [914 mm]
  • Gear length: 37.6” [955 mm]
  • Gear length + top extension length = overall length
  • Roller release trigger located at 42 1/2″ up from bottom of door panel
  • Lower Roller pin lock point located at 6 7/16″ from bottom of lock

Variations available:

Activation Types:  Manual Activation,  Automatic Activation and Electronic Activation.

Multipoints:    For Automatic Multipoint Lock Systems – Available in Tongue and Roller pin Versions only. For Manual Activated multipoint lock systems, Hook bolt, Round bolt, Tongue and Roller Pin version are available.

Faceplate Widths:  16mm (5/8″) and 20mm (3/4″)

Backset Variations:  Hoppe only offers the following (4) Backsets – 35mm (1 3/8″) ,  45mm (1 3/4″) ,  60mm  (2 3/8″) and  70mm (2 3/4″).

 

Click on the “Part Number” to take you to the product page.

Part Number Lock Part Locking Point Extension Length Overall Top Extension + Gear = Door Panel Height  Roller & Release Trigger Location from bottom of door up
8778515 Top Extension Roller 1045mm – 41 1/8″ Use For Door Panel Heights Between                           71 1/16″   –   78 1/4″  Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 64 3/4″
8778519 Top Extension Roller 1220mm  – 48″  Use For Door Panel Heights Between                           71 1/16″   –   85 5/8″  Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 72 9/16″
8778523 Top Extension Roller 1395mm –54 15/16″   Use For Door Panel Heights Between                           79 1/8″  –  92 1/2″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 80 5/8″
8778527 Top Extension Roller 1570mm –61 13/16″   Use For Door Panel Heights Between                           79 1/8″  –  99 7/16″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 86 9/16″
8778531 Top Extension Roller 1745mm-68 11/16″   Use For Door Panel Heights Between                        88 3/4″  –  106 5/16″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 86 9/16″
8778535 Top Extension Roller 1920mm –75 9/16″   Use For Door Panel Heights Between                        104 1/2″  –  113 1/8″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 99″
8778539 Top Extension Roller 2095mm- 82 7/16″   Use For Door Panel Heights Between                        104 1/2″  –  120 1/16″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 99″
8778543 Top Extension Roller 2270mm – 89 3/8″   Use For Door Panel Heights Between                        104 1/2″  –  126 15/16″ Roller release trigger @ 42 1/2″  / Upper Roller lock point @ 99″
Part Number Lock Part Locking Point Backset Dead Bolt Throw Roller Lock Point From Bottom of Door Up
8778275 Gear Roller 35mm (1.38) 14mm   –  1/2″ Bottom Roller @  6  7/16″ up
8778307 Gear Roller 45mm (1.77) 14mm   –   1/2″ Bottom Roller @  6  7/16″ up
8778251 Gear Roller 35mm (1.38) 25.4mm   –   1″ Bottom Roller @  6  7/16″ up
8778295 Gear Roller 45mm (1.77) 25.4mm    –   1″ Bottom Roller @  6  7/16″ up

Advantages of the Hoppe 8778275 Automatic Multipoint Door Locking System.

Hoppe multipoint door lock are the absolute best multi point lock to have installed on your hurricane rated impact door. The multipoint lock bodies are made of stainless steel and is perfect for any environment. We have seen many of the older multipoint lock systems such as FUHR and G.U., corrode and rust out in seacoast conditions. In the future when you change your locks Hoppe is a great brand to go with.

  • Keep your home secure with weather, fault and intrusion resilient Hoppe multi-point door locks
  • Approved for Hurricane HVHZ zones
  • Easily open and close your door with minimal effort.

Multipoint locks and what to do if they happen to fail.

When multipoint door locks fail, you may have a difficult time locking and securing your home. Hoppe locks are a specialty lock and cannot be found at the local hardware store. Integral Windstorm Products is a proud dealer and distributor of Hoppe Multi-point door locks. Hoppe locks are sold through authorized dealers only. The problem with online purchases of multipoint locks are the availability. When you purchase a lock online, it still may take 2-6 weeks to receive your lock. Hoppe makes all of their multipoint locking systems to order. So if the dealer that sold you the lock doesn’t have it in stock, they will order it.

We try to keep Hoppe lock products in stock for you to order.

Multipointdoorlocks.com will always try to keep the most popular units in stock. Due to sporadic high volume orders coming in nationally, we do run out occasionally. We do our best effort to avoid this, but it happens. Hoppe manufactures all products to order and can have a lead time of 2-3 weeks. Some items that are not kept in stock, have to be ordered directly from Hoppe and shipped to you.

If you are having problems finding your locks and components, Please fill out the questionnaire below. We are here to help.

Multipoint Lock Questionnaire Form
This is necessary to determine which manufacturer and series you will need.
Example: Black, Stainless steel, Goldtone
The "faceplate" is the metal strip on the entire edge of the door. It is the lock strip plate that the dead bolt and striker engages through.
If you found a symbol and do not know what it is, Select "Found a Symbol, Not Sure"

 

Additional information

Dimensions 43 × 5 × 5 in
Manufacturer

Hoppe

Product Number

8778275

Series

HLS-9000 Series

Lock Engagement

Automatic Engagement

Locking Point

Automatic Roller Pin

Backset Width

35mm – 1 3/8" measured from edge of door to center of handle

PZ Measurement

92mm – 3 5/8" measured from center of handle to center of keyhole

Deadbolt Throw

14mm – 1/2" projection

Faceplate Width

16mm – 5/8" wide

Automatic Trigger Location

Roller Release Trigger Pin is located at 42 1/2" measured from the bottom of door panel up to the center of the trigger pin.

Bottom Roller Pin Locking Point

Roller Pin Located at 6 7/16" measured from the bottom of the door panel to the center of the roller pin.

Top Roller Pin Locking Point

Various – Refer to the individual Top Extension specifications for top roller pin location.

Return Policy

Please be absolutely sure of the lock components you are seeking and read all the specifications before placing your order. Hoppe manufactures all components to order, therefore does not accept returns. All sales are finale and returns are not accepted.

error: Alert: Content is protected !!