IWP-35-92-14 Hoppe Gear Box – HLS-9000 Series, 35/92/14

$197.89

IWP-35-92-14 Hoppe Lock Gear- Repairs sagging or drooping door handles on Doors with Hoppe HLS-9000 series locks.

Available on backorder

SKU: IWP-35-92-14 Categories: , , Tags: , , , , Product ID: 15012

Description

IWP-35-92-14 Hoppe Gear Box.

The IWP-35-92-14 Hoppe Gear Box makes is easy to repair your Hoppe Multi-point Door Lock.

This works on all Hoppe HLS-9000 series. Manual Operation, Multipoint Lock Gear, 16mm Faceplate, Handle Above Thumb Turn, 35mm Backset, 14mm deadbolt throw.

If you are not sure if this is the solution to repairing your lock, and would like to purchase the entire lock body, click here to fill out the information detail form for us to find your lock. 

 

Hoppe multipoint door locks are the absolute best multi point lock to have installed on your hurricane rated impact door. The IWP-35-92-14 Hoppe Lock Gear Box will repair all Hoppe multipoint locks with a mis-handling device.

Earlier Hoppe locks did not have this feature and must be replaced with an entirely new lock body. If you have an earlier model without a mis-handling device just above the deadbolt, please fill out the form below. This will help us locate your new Hoppe Replacement Lock.

  • It is also important for you to replace your house or condo locks especially if you live near the ocean because of these reasons:
  • Salt can rot the wood and does damage to locks as well if not cleaned and serviced periodically.
  • Keep your home secure with weather, fault and intrusion resilient Hoppe multi-point door locks
  • Approved for Hurricane HVHZ zones in Florida Miami-Dade Counties
  • Easily open and close your door with minimal effort.
IWP-35-92-35 Hoppe Gear box to repair drooping or sagging handle on multi-point door lock
IWP-35-92-35 Hoppe Gear box
Hoppe Lock gear boxes for lock repair hls-9000
Hoppe Lock Gear Box Replacements

hoppe lock gear box replacement

What is a replacement Hoppe Gear Box?

A replacement gear box is the mechanism that drives all motion of the lock itself. This is activated by the handle and the profile cylinder. When the internal gear cog teeth wear down, the lock is difficult to operate. The Lock feels like it is slipping when lifting up the handle. You may also hear a “clicking noise” from the gear teeth skipping inside. On a Hoppe HLS-9000 manual activated lock, this is a direct replacement for these multi-point door locks, and it is super easy to install. This gear box replacement will restore the operation of your Hoppe Door lock. It is also the solution to repair a handle that is hanging downward. You can easily fix the sagging handle or dreaded drooping handle.

Component Specifications:

Below are the exact details of this particular Hoppe manual gear box replacement.

Component Details

Brand:      Hoppe
Series:      HLS-9000, Handle Above European Profile Cylinder
Configuration:   Repairs All Hoppe Multi-point Locking Systems equipped with a mis-handling device
Component:     Locking Gear Box Only - Faceplate not included
Model Number:    IWP-35-92-14
Activation:      Manual Activation, Multi-points activate when lifting lever handle, Then Turn thumb turn to lock securely.
Faceplate Width:    16mm (5/8")  Not Included    
Lock Points:      N/A - Works on all HLS - 9000 Locks with a 35mm Backset and a 14mm Deadbolt
Handle Height:     36" From Bottom of Door to Center of Handle.
Backset:      35mm (1 3/8")  Measurement from Edge of Door to Center of Handle
PZ Dimension:    92mm (3 5/8") Center of Handle to Center of Key Hole.
Dead Bolt Throw:    14mm ( 1/2") Center of Handle to Center of Key Hole.
Lock Cylider:      European Profile Lock Cylinder Only - Will not work with American lock cylinders or trimsets
Handing:      Reversible - Works on Left or Right Hinged Door handing configurations

 

Reasons why to replace the gear box and how they get broken:

Crunchy or ratcheting noise:         This is due to the teeth on the drive cog, they are stripped or worn out. This part cannot be replaced. A new gear box is needed

Sagging Lever Handle:         This is due to the internal return spring is broken. This part cannot be replaced. A new gear box is needed.

Drooping Lever Handle:         This is due to the internal return spring is broken. This part cannot be replaced. A new gear box is needed.

Handle Hangs Down:         This is due to the internal return spring is broken. This part cannot be replaced. A new gear box is needed.

Lock is Frozen:         The lock is jammed and door will not open. Lock may need to be cut out to open the door. A new gear box is needed

 

Advantages of installing a new IWP-35-92-14 Hoppe Lock Gear Box to your existing Hoppe Multipoint Door Locking System.

  • Make the existing lock close and latch like new.
  • Smoother lock activation when lifting the handle upwards to engage thee locking points
  • Repairs drooping and sagging lever handles. New return spring inside the lock gear box returns handle to horizonal position.
  • Easy installation, READ INSTRUCTION BELOW
  • Fast Shipping and Usually always in stock and ready to ship.
  • Hoppe Gear Boxes are manufactured by Hoppe.
  • Exact match replacement part (for locks with mis-handling device)

How to install  and replace you current broken Hoppe lock.

You can watch Hoppe’s Replacement video here      Watch Youtube Video

  1. Remove entire lock body from your door panel
  2. Remove the lock gear box mechanism from the stainless steel faceplate. Screw driver needed.
  3. Change the handing on the new lock gear box to resemble the old lock handing. do a side by side inspection.
  4. To change handing, use pliers to grab the striker and pull outwards enough to rotate the striker to the handing you need.
  5. Do the same to the small striker (Mishandling device).
  6. Put lock gear to faceplate
  7. Attach drive bar on faceplate to the new lock gear box
  8. Screw faceplate on to the new lock gear box
  9. Test new lock to make sure drive gear is connected
  10. Install lock back into door and connect top drive bar to lock gear
  11. Screw top extension to lock gear
  12. Test lock to make sure all lock points activate and disengage properly
  13. Re-install handle set and profile cylinder, Check again that all parts work properly before you close the door into the door frame.
  14. The door should close and lock if all steps have been followed properly, And that’s it!!!!

Multipoint locks and what to do if they happen to fail.

When multipoint door locks fail, you may have a difficult time locking and securing your home. Hoppe locks are a specialty lock and cannot be found at the local hardware store. Integral Windstorm Products is a proud dealer and distributor of Hoppe Multi-point door locks. Hoppe locks are sold through authorized dealers only. The problem with online purchases of multipoint locks are the availability. When you purchase a lock online, it still may take 2-6 weeks to receive your lock. Hoppe makes all of their multipoint locking systems to order. So if the dealer that sold you the lock doesn’t have it in stock, they will order it.

We try to keep Hoppe lock products in stock for you to order.

Multipointdoorlocks.com will always try to keep the most popular units in stock. Due to sporadic high volume orders coming in nationally, we do run out occasionally. We do our best effort to avoid this, but it happens. Hoppe manufactures all products to order and can have a lead time of 2-3 weeks. Some items that are not kept in stock, have to be ordered directly from Hoppe and shipped to you.

If you are having problems finding your locks and components, Please fill out the questionnaire below. We are here to help.

Multipoint Lock Questionnaire Form
This is necessary to determine which manufacturer and series you will need.
Example: Black, Stainless steel, Goldtone
The "faceplate" is the metal strip on the entire edge of the door. It is the lock strip plate that the dead bolt and striker engages through.
If you found a symbol and do not know what it is, Select "Found a Symbol, Not Sure"

 

Additional information

Weight 4 lbs
Dimensions 11 × 6 × 2 in
Manufacturer

Hoppe

Product Number

IWP-35-92-14

Series

HLS-9000 Series

Lock Engagement

Manual Engagement

Locking Point

Works on all Hoppe HLS-9000 multi-point locks

Backset Width

35mm – 1 3/8" measured from edge of door to center of handle

PZ Measurement

92mm – 3 5/8" measured from center of handle to center of keyhole

Deadbolt Throw

14mm – 1/2" projection

Faceplate Width

16mm – 5/8" wide ( Faceplate not included )

Handing

Replaces broken gear boxes on left and right hinged doors

Lock Cylinder

European Profile lock cylinders only – WILL NOT WORK WITH AMERICAN LOCK CYLINDERS

Mis-Handling Device

Yes – All gear box replacements now are equipped – WILL NOT REPLACE OLDER HOPPE LOCKS THAT ARE NOT EQUIPPED WITH A MIS-HANDLING DEVICE JUST ABOVE THE DEADBOLT.

Return Policy

Please be absolutely sure of the lock components you are seeking and read all the specifications before placing your order. Hoppe manufactures all components to order, therefore does not accept returns. All sales are finale and returns are not accepted.

error: Alert: Content is protected !!