8778887 Hoppe Manual Roller Pin Lock – No Shootbolt with Roller Pins at 6 7/16″ and 20 1/4″

Hoppe Manual Roller Pin Lock without Bottom Shootbolt – HLS-9000 Series  -16mm Faceplate, Roller Pins @ 6 7/16″ & 20 1/4″ from bottom. 45mm Backset, 14mm deadbolt throw.

If you are not sure about the Manual Lock Gear with Roller Pins and No Bottom Shootbolt

or lock components you need,         Click Here to have us help you find them.

 

Hoppe multipoint roller pin locks are some of the absolute best multi point lock to have installed on your hurricane rated impact door. The multipoint lock bodies are made of stainless steel and is perfect for any environment. We have seen many of the older multipoint lock systems such as FUHR and G.U., corrode and rust in seacoast conditions. In the future when you change your locks Hoppe is a great brand to go with.

Hoppe automatic lock for weather shield lock repairTherma tru doors with Hoppe multipoint tongue lock with bottom shootboltHurd peachtree and weather shield french doors with Hoppe multipoint tongue locks with shootbolts

  • It is also important for you to replace your house or condo locks especially if you live near the ocean because of these reasons:
  • Salt can rot the wood and does damage to locks as well if not cleaned and serviced periodically.
  • Keep your home secure with weather, fault and intrusion resilient Hoppe multi-point door locks
  • Approved for Hurricane HVHZ zones in Florida Miami-Dade Counties
  • Easily open and close your door with minimal effort.
  • Repairs Locks on Weather Shield Hurd Kolbe Thermatru Therma-Tru Peachtree doors with multipoint door locks with Hoppe manual tongue locks.

 

#8778887 – Component Specifications:

Below are the exact details of this particular Hoppe Manual   Roller Pin Lock without Shootbolt component. Other variations are available.

Component Details

Brand:                        Hoppe Series: HLS-9000, Handle Above European Profile Cylinder
Configuration:           Multi-point Roller Pin Lock only, Does not lock at top and bottom, No Shoot Bolt
Component:               Locking Gear
Model Number:          8778887
Backset:                      45mm (1 3/4″)  Measurement from Edge of Door to Center of Handle
Dead Bolt Throw:       14mm ( 1/2″) Center of Handle to Center of Key Hole.
Activation:                  Manual, Lift handle to engage roller pins, Turn thumb turn to lock deadbolt securely.
Faceplate Width:        16mm (5/8″)
Lock Points:                2 Roller Pin locking points –   6 7/16″ & 20 1/4″ on 4 roller systems
Handle Height:            36″ From Bottom of Door to Center of Handle.
Door Brands Used on:     Weather Shield, Jeld-Wen, Sierra Pacific, Peachtree, Hurd, Kolbe, Therma-Tru

 

 

  • 2 Roller Pin shifts downwards on the lock body, 2 roller pins above the latch. roller pins lock into side jamb or in-active door panel, when door handle is lifted and lock is engaged.
  • Turn thumb turn to lock
  • Combine Top Extension with Gear for complete lock
  • Faceplate width: 16mm
  • Handle height: 36” [914 mm]
  • Lock Gear length: 37.6” [955 mm]

 

 

Click on the   “Part Number”  below to take you to the product page.

Hoppe HLS-9000 Multipoint Lock with Roller pin           Only 1 Roller Pin on Lock, and only 1 roller in on top extension

2 Roller Pin Units –  1 above and 1 below Deadbolt Area. 

Gear Lock Points:                Roller Pin locking point    6 7/16 ” on 2 roller systems
Part Number Lock Part Locking Point Extension Length Overall Length
(with 914mm 36″ Handle Height)
Roller Pin Location
8778479 Top Extension Roller 1045mm – 41 1/8″       Door Panels Between   67 15/16″ – 78 3/4″ 64 3/4″ from bottom of door panel                                                                                          
8778483 Top Extension Roller 1220mm – 48″           Door Panels Between    75 3/4″ – 85 5/8″ 72 9/16″ from bottom of door panel
8778487 Top Extension Roller 1395mm  – 54 15/16″ Door Panels Between   83 13/16 – 92 1/2″ 80 11/16″ from bottom of door panel
8778491 Top Extension Roller 1570mm  – 61 13/16″ Door Panels Between   89 3/4″ – 99 7/16″ 86 9/16″ from bottom of door panel
8778495 Top Extension Roller 1745mm  – 68 11/16″ Door Panels Between   89 3/4″ – 106 5/16″ 86 9/16″ from bottom of door panel
Part Number Lock Part Locking Point Backset Dead Bolt Throw Roller Pin Location
8778279 Gear 1 Roller @ 6 7/16″ from bottom,  No Shootbolt               35mm   (1 3/8″) 14mm   (1/2″) 6 7/16″ up from bottom of door
8778511 Gear 1 Roller @ 6 7/16″ from bottom,  No Shootbolt 45mm (1 3/4″”) 14mm   (1/2″) 6 7/16″ up from bottom of door
8778255 Gear 1 Roller @ 6 7/16″ from bottom,  No Shootbolt  35mm   (1 3/8″) 25.4mm (1″) 6 7/16″ up from bottom of door
8778223 Gear 1 Roller @ 6 7/16″ from bottom,  No Shootbolt  45mm (1 3/4″”) 25.4mm (1″) 6 7/16″ up from bottom of door

 

 

Click on the   “Part Number”  below to take you to the product page.

 

Hoppe HLS-9000 Multipoint Lock with Roller pin           2 Roller pins on Lock, and 2 roller pins on top extension

4 Roller Pin Units –  2 above and 2 below Deadbolt Area

Gear Lock Points:                Roller Pin locking point    6 7/16″ & 20 1/4″ on 4 roller systems
Part Number Lock Part # of Roller Pins per component / part Extension Length Overall Length
(with 914mm 36″ Handle Height)
Roller Pin Locations (From the bottom of door panel up to Roller Pin)
8778851 Top Extension 2x Roller 1045mm –   41 3/16″               Door Panels Between  70 5/8″ – 78 1/4 Roller Pin #3 – 51 3/4″,      Roller Pin #4 – 67 1/2″                                                                                                                                    
8778855 Top Extension 2x Roller 1220mm –   48″ Door Panels Between  70 5/8″ – 85 5/8″ Roller Pin #3 – 51 3/4″,      Roller Pin #4 – 67 1/2″
8778859 Top Extension 2x Roller 1395mm  –   54 15/16″ Door Panels Between  84 1/2″– 92 1/2″ Roller Pin #3 – 59 5/8″”,      Roller Pin #4 – 81 1/4″
8778863 Top Extension 2x Roller 1570mm –   61 13/16″ Door Panels Between  84 1/2 – 99 7/16″ Roller Pin #3 – 59 5/8″”,      Roller Pin #4 – 81 1/4″
8778867 Top Extension 2x Roller 1745mm –   68 11/16″ Door Panels Between  98 1/4″ – 106 5/16″ Roller Pin #3 – 67 1/2 “,      Roller Pin #4 – 95”
8778871 Top Extension 2x Roller 1920mm –   75 9/16″ Door Panels Between  98 1/4″ – 113 3/16″ Roller Pin #3 – 67 1/2 “,      Roller Pin #4 – 95”
8778875 Top Extension 2x Roller 2095mm –   82 1/2″ Door Panels Between  112″ – 120 1/16″ Roller Pin #3 – 75 3/8 “,      Roller Pin #4 – 108 13/16”
8778879 Top Extension 2x Roller 2270mm  –   89 3/8″ Door Panels Between  112″ – 127″ Roller Pin #3 – 75 3/8 “,      Roller Pin #4 – 108 13/16”
Part Number Lock Part Locking Point Backset Dead Bolt Throw Roller Pin Locations (From the bottom of door panel up to Roller Pin)
8778883 Gear 2 Rollers –  (1 @ 6 7/16″, 1 Roller Pin @ 20 1/4″ from bottom),  No Shootbolt 35mm   (1 3/8″) 14mm   (1/2″) Roller Pin #1 –  6 7/16″       Roller Pin #2 – 20 1/4″
8778887 Gear 2 Rollers –  (1 @ 6 7/16″, 1 Roller Pin @ 20 1/4″ from bottom),  No Shootbolt 45mm (1 3/4″”) 14mm   (1/2″) Roller Pin #1 –  6 7/16″       Roller Pin #2 – 20 1/4″
8778891 Gear 2 Rollers –  (1 @ 6 7/16″, 1 Roller Pin @ 20 1/4″ from bottom),  No Shootbolt 35mm   (1 3/8″) 25.4mm (1″) Roller Pin #1 –  6 7/16″       Roller Pin #2 – 20 1/4″
8778895 Gear 2 Rollers –  (1 @ 6 7/16″, 1 Roller Pin @ 20 1/4″ from bottom),  No Shootbolt 45mm (1 3/4″”) 25.4mm (1″) Roller Pin #1 –  6 7/16″       Roller Pin #2 – 20 1/4″

 

Where to Buy Hoppe 8778887 Manual  Multipoint Roller Pin Locking System.

Hoppe multipoint door lock are the absolute best multi point 4 Roller Pin lock to have installed on your hurricane rated impact door. The multipoint 2 Roller Pin lock bodies are made of stainless steel and is perfect for any environment. We have seen many of the older multipoint lock systems such as FUHR and G.U., corrode and rust out in seacoast conditions. In the future when you change your tongue lock, Hoppe is a great brand to go with.

  • Keep your home secure with weather, fault and intrusion resilient Hoppe multi-point door locks
  • Approved for Hurricane HVHZ zones
  • Easily open and close your door with minimal effort.

Multipoint locks and what to do if they happen to fail.

When multipoint door locks fail, you may have a difficult time locking and securing your home. Hoppe locks are a specialty lock and cannot be found at the local hardware store. Integral Windstorm Products is a proud dealer and distributor of Hoppe Multi-point door locks. Hoppe locks are sold through authorized dealers only. The problem with online purchases of multipoint locks are the availability. When you purchase a lock online, it still may take 2-6 weeks to receive your lock. Hoppe makes all of their multipoint locking systems to order. So if the dealer that sold you the lock doesn’t have it in stock, they will order it.

We try to keep Hoppe lock products in stock for you to order.

Multipointdoorlocks.com will always try to keep the most popular units in stock. Due to sporadic high volume orders coming in nationally, we do run out occasionally. We do our best effort to avoid this, but it happens. Hoppe manufactures all products to order and can have a lead time of 2-3 weeks. Some items that are not kept in stock, have to be ordered directly from Hoppe and shipped to you.

If you are having problems finding your locks and components, Please fill out the questionnaire below. We are here to help.

Multipoint Lock Questionnaire Form
This is necessary to determine which manufacturer and series you will need.
Example: Black, Stainless steel, Goldtone
The "faceplate" is the metal strip on the entire edge of the door. It is the lock strip plate that the dead bolt and striker engages through.
If you found a symbol and do not know what it is, Select "Found a Symbol, Not Sure"

 

error: Alert: Content is protected !!