Hoppe Lock Gear Box Replacement – 1 3/4 backset, 1″ Deadbolt

$197.22

Hoppe Lock Gear Box replacement part to repair broken multipoint door locks.

Available on backorder

Description

Hoppe Lock Gear Box  – 1 3/4 Backset,  3 5/8″, PZ – 1″ Deadbolt throw. Fixes Drooping lever handle.

 

Need a Hoppe lock gear box to repair your broken Hoppe door lock? Do you need a replacement part to repair your Hoppe multipoint door lock with a drooping or sagging lever handle? You need a new Hoppe Lock Gear Box replacement of your sagging or drooping handle on your Hoppe door lock. This model of multi-point lock is manual activation, for 16 mm stainless steel faceplate. This is for the active door on a single or double door. For double door installations, this lock relies on the inactive door lock. Inactive doors typically have top and bottom shoot bolts. When the active door is closed and locked, the active panel locks into the inactive panel.

Now you can fix that drooping handle on your Hoppe door lock. With a new Hoppe Lock gear box, you can repair the sagging lever handle issue.

Hoppe Lock Gear Box to repair broken door lock sagging handle and drooping lever handles

Hoppe Multipoint door lock gear box to repair drooping sagging door handle

Hoppe Lock Gear Box Replacement - 1 3/4 backset, 1" Deadbolt Hoppe Lock Gear Box,hoppe lock,drooping handle,sagging handle,broken lock <h3>Hoppe Lock Gear Box replacement part to repair broken multipoint door locks.</h3>

Therma-Tru door lock replacement part with Hoppe multi-point door lock

 

 

This part will replace all drive gears on all HLS-9000 locks that have the following:

  1. Handle must be over the thumb turn and profile cylinder. (This is typical of all Hoppe Hls-9000 series multipoint door locks)
  2. Center of handle to center of thumb turn must be 92mm / 3 5/8″ (This is typical of all Hoppe Hls-9000 series multipoint door locks)
  3. Backset must be 45mm / 1 3/4″  (Very Important, Measure from Edge of Door Panel to Center of Handle)
  4. Must have a European profile cylinder that is removable when attachment screw on the edge of door panel has been removed.
  5. This part works only on HLS-9000 multipoint door locks only. It will not work on single point lock applications

Lock Configurations that this part is a direct replacement for:

  • HLS-9000 series with or without bottom shootbolts
  • HLS-9000 series with round bolt locking points
  • HLS-9000 series with tongue type locking points
  • HLS-9000 series with roller pin locking points
  • HLS-9000 series with hook bolt locking points

Specifications:

  • Hoppe lock gear box – #IWP-1 3/4-3 5/8-1
  • 45mm backset (1 3/4″       from edge of door to center of door handle)
  • Locking point: Strike Latch and deadbolt (replacement gear box for all HLS-9000 locking systems.)
  • 25mm (1″) deadbolt throw  (NOTE:  25mm (1″) DEADBOLT THROW AVAILABLE – PLEASE DOUBLE CHECK BEFORE ORDERING)
  • 16mm    (5/8″)  Stainless steel faceplate (Not Included)
  • 92mm (3 5/8″) from center of handle to center of thumb turn
  • Accepts European lock cylinder only.    Handle over thumb turn. Need American cylinder? Search Hoppe HLS-7 Series.
  • Works on both left swing and right swing doors

How to install  and replace you current broken lock.

You can watch Hoppe’s Replacement video here      Watch Youtube Video

  1. Remove entire lock body from your door panel
  2. Remove the lock gear box mechanism from the stainless steel faceplate. Screw driver needed.
  3. Change the handing on the new lock gear to resemble the old lock handing. do a side by side inspection.
  4. To change handing, use pliers to grab the striker and pull outwards enough to rotate the striker to the handing you need.
  5. Do the same to the small striker (Mishandling device).
  6. Put lock gear to faceplate
  7. Attach drive bar on faceplate to the new lock gear box
  8. Screw faceplate on to the new lock gear box
  9. Test new lock to make sure drive gear is connected
  10. Install lock back into door and connect top drive bar to lock gear
  11. Screw top extension to lock gear
  12. Test lock to make sure all lock points activate and disengage properly
  13. Re-install handle set and profile cylinder, Check again that all parts work properly before you close the door into the door frame.
  14. The door should close and lock if all steps have been followed properly, And that’s it!!!!

 

Hoppe Product Page to view the entire product description

Additional information

Dimensions 6 × 10 × 2 in
Brand

Hoppe HLS-9000 Replacement Locking Gear

Part Number

IWP-1 3/4-3 5/8-1

Series

HLS-9000 Gear Box Only

Backset

45mm (1 3/4") Backset from edge of door panel to center of thumb turn

Handle Configuration

Handle Over Thumbturn (HLS-9000 Series)

Locking Point Type

Replacement for all HLS-9000 locking systems with drooping or Sagging lever handle.

PZ Dimension

92mm (3 5/8" from center of handle to center of thumbturn.

Deadbolt Throw

25mm (1" deadbolt travel)

Key Cylinder Type

Accepts only European key cylinders

Return / Refund Policy

Please be absolutely sure that this product is in fact the product that you need, selected and intend to order. These locks are special order and made to order from the factory. THIS PRODUCT IS NON-RETURNABLE AND NON-REFUNDABLE. Please confirm all specifications before any order is placed.

Replacement Compatibility

Hoppe Lock Gear Box replacement will replace all broken lock gear boxes on HLS-9000 locking systems. Back set measurement ( In product specification ) and deadbolt throw (Typically 1″ )may be different than the one you presently have on your locking system. Verify first that any differences will work on your door and no conflicts will occur

You may also like…